TM 11-6610-202-34P
(3) Recoverability code.
Recoverability
abbreviation (e.g., ea, in, pr, etc). When the unit of
measure differs from the unit of issue, the lowest unit of
codes are assigned to support items to indicate the
issue that will satisfy the required units of measure will
disposition action on unserviceable items.
The
be requisitioned.
recoverability code is entered in the fifth position of the
h. Quantity Incorporated in Unit. Indicates the
Uniform SMR Code format as follows:
Recoverability
quantity of the item used in the breakout shown on the
codes
Definition
illustration figure, which is prepared for a functional
group, subfunctional group, or an assembly.
Z-
Nonreparable item.
When unserviceable,
condemn and dispose at the level indicated
4.
Special Information
in position 3.
National stock numbers (NSN's) that are missing from P
F-
Reparable item.
When uneconomically
source coded items have been applied for and will be
reparable, condemn and dispose at the
added to this TM by future change/revision when they
direct support level.
are entered in the Army Master Data File (AMDF). Until
H-
Reparable item.
When uneconomically
the NSN's are established and published, submit
reparable, condemn and dispose at the
exception requisitions to:
Commander, US Army
general support level.
Communications-Electronics Command and
Fort
D-
Reparable item. When beyond lower level repair
Monmouth, ATTN: DRSEL-MM, Fort Monmouth, New
capability, return to depot. Condemnation
Jersey 07703 for the part required to support your
and disposal not authorized below depot
equipment.
level.
5.
How to Locate Repair Parts
L-
Reparable item. Repair, condemnation, and
a. When National stock number or part
disposal
not
authorized
below
number is unknown.
depot/specialized repair activity level.
(1) First. Using the table of contents,
c. National Stock Number.
Indicates the
determine the functional group within which the item
National stock number assigned to the item and will be
belongs.
This is necessary since illustrations are
used for requisitioning purposes.
prepared for functional groups and listings are divided
d. Federal Supply Code for Manufacturer
into the same groups.
(FSCM).
(2) Second. Find the illustration covering
The FSCM is a 5-digit numeric code listed in SB 708-41/
the functional group to which the item belongs.
42 which is used to identify the manufacturer, distributor,
(3) Third.
Identify the item on the
or Government agency, etc.
illustration and note the illustration figure and item
e. Part Number. Indicates the primary number
number of the item.
used by the manufacturer (individual, company, firm,
(4) Fourth. Using the Repair Parts Listing,
corporation, or Government activity), which controls the
find the figure and item number noted on the illustration.
design and characteristics of the item by means of its
b. When National stock number or part
engineering drawings, specifications, standards, and
number is known.
inspection requirements to identify an item or range of
(1) First. Using the Index of National
items.
Stock Numbers and Part Numbers, find the pertinent
NOTE
National stock number or part number. This index is in
When a stock numbered item is
NIIN sequence followed by a list of part numbers in
alphameric sequence, cross-referenced to the illustration
requisitioned, the repair part received
figure number and item number.
may have a different part number
(2) Second. After finding the figure and
than the part being replaced.
item number, locate the figure and item number in the
f.
Description. Indicates the Federal item
repair parts list.
name and, if required, a minimum description to identify
6.
Abbreviations
the item.
Not applicable.
g. Unit of Measure (U/M).
Indicates the
(Next printed page is 4)
standard of the basic quantity of' the listed item as used
in performing the actual maintenance function. This
measure is expressed by a two-character alphabetical
2
